Marine & Offshore Cables TEBAOFLEX

TF-OWIND Offshore Wind Monopile, Jacket & Mooring Chain Cleaning & NDT Crawler Dynamic Umbilical Cable (690 V–3.3 kV)

TF-OWIND (TF-OWIND-UMB) is a splash-zone wave-fatigue-resistant dynamic electro-optical umbilical cable (690/1,000 V AC to 1.8/3.0 (3.3) kV, 22 kN to 110 kN minimum breaking load) engineered for offshore wind turbine monopile marine-growth cleaning ring crawlers, jacket-leg cavitation jetting vehicles, subsea weld PAUT/ACFM NDT scanners and floating-wind mooring chain inspection crawlers.

Product information
SKU
TF-OWIND-UMB
Brand
TEBAOFLEX
Product overview

TF-OWIND offshore wind cleaning and NDT crawler umbilical cables deliver 690/1,000 V AC to 1.8/3.0 (3.3) kV drive and high-pressure pump power, stainless-steel tube optical telemetry, gigabit Cat 6A data and low-loss 75-ohm ultrasonic coax inside Ø 16.8 mm to Ø 35.4 mm torque-balanced cross-sections rated from 22 kN to 110 kN minimum breaking load.

Offshore wind foundation maintenance — removing 100–300 mm thick mussel, kelp and barnacle marine growth from monopiles, transition pieces (TP), boat landings, ICCP anodes and floating-wind mooring chains prior to structural weld phased-array ultrasonic testing (PAUT), TOFD or alternating-current field measurement (ACFM) — subjects umbilicals to brutal splash-zone orbital wave slamming against steel piles and subsea rock-berm scour protection. Ordinary ROV tethers suffer rapid outer-jacket cuts on crushed mussel shells and conductor corkscrewing when wave troughs snap-load the catenary. TF-OWIND counters snap loads with contra-helical aramid/LCP strength braids, elastomeric bedding cushions, dry longitudinal water-blocking and extra-thick Shore 95A cut-resistant Neon Yellow or Fluorescent Orange polyether PUR sheaths.

Available in seven standard schedules spanning monopile marine-growth removal (TF-OWIND-MGR15, MGR37, MGR75), 3.3 kV floating-wind mooring chain crawlers (TF-OWIND-CHAIN3K), and multi-coax/STP weld NDT scanners (TF-OWIND-NDT-PAUT, NDT-ACFM, ROV-HYB). Supplied from 50 m MOQ as continuous bulk cable in 7 to 45 working days.

Explore the marine, offshore and shipboard cable range for related configurations.

Construction

TF-OWIND Splash-Zone Cleaning & NDT Umbilical Construction

Built around crush-protected optical/coax NDT telemetry, fine-stranded Class 5/6 power conductors, snap-load-absorbing contra-helical synthetic armor and mussel-cut-resistant Shore 95A PUR sheaths.

Clean 2D circular engineering cross-section of TF-OWIND offshore wind cleaning and PAUT NDT crawler umbilical showing thick fluorescent-orange PUR outer jacket, dual contra-helical aramid braids, elastomeric cushion bedding, three 690 V tinned-copper power cores, shielded data/coax units and central stainless FIMT fiber tube
Cross-section: heavy-wall PUR jacket and elastomeric wave-slam cushion protect power, Cat 6A, 75-ohm PAUT coax and FIMT optical elements.
TF-OWIND Offshore Wind Monopile, Jacket & Mooring Chain Cleaning & NDT Crawler Dynamic Umbilical Cable (690 V–3.3 kV) construction
ComponentMaterial and construction
1. Class 5/6 Tinned Copper 690 V–3.3 kV Power ConductorsIEC 60228 Class 5 or Class 6 flexible tinned copper conductors (1.5 mm² to 25 mm²) insulated with high-dielectric XLPE or crosslinked EPR/HEPR for VFD thruster, magnetic-wheel and cavitation-pump drives.
2. FIMT Single-Mode Fibers, Subsea Cat 6A & 75-Ohm PAUT Coaxial Cores4 to 12 ITU-T G.657.A2 fibers in a hermetically welded stainless-steel tube (FIMT), paired with 100-ohm foil/braid-screened Cat 6A or multi-channel low-capacitance 75-ohm coaxial / STP ultrasonic NDT cores.
3. Elastomeric Wave-Slam Cushion & Longitudinal Water-BlockingExtruded TPE/PUR inner bedding absorbs radial impact against monopile boat-landing rungs while silicone/solid water-blocking compound and swelling tapes prevent axial seawater migration.
4. Dual Contra-Helical Aramid or LCP Torque-Balanced Strength BraidOpposed-lay high-modulus aramid or liquid-crystal-polymer (LCP) braids deliver 22 kN to 110 kN minimum breaking load (5.5 kN to 27.5 kN safe working load) with near-zero torque under wave heave.
5. Heavy-Wall Shore 95A Mussel- & UV-Resistant Subsea PUR Sheath2.5–4.0 mm thick hydrolysis-, oil- and UV-stabilized Shore 95A matte polyether PUR in high-visibility Fluorescent Orange or Neon Yellow for SOV/CTV crane-sheave and splash-zone visibility.

TF-OWIND MGR, CHAIN3K & PAUT/ACFM Series Breakdown

  • TF-OWIND-MGR15 / 37 / 75: 15 kW to 75 kW (690/1,000 V) splash-zone monopile and jacket-leg marine-growth cleaning crawler umbilicals (32–85 kN MBL)
  • TF-OWIND-CHAIN3K: 1.8/3.0 (3.3) kV medium-voltage high-load (110 kN MBL) umbilical for 300 m floating offshore wind mooring chain cleaning & caliper crawlers
  • TF-OWIND-NDT-PAUT / ACFM: Multi-coax (75-ohm) and multi-STP (100-ohm) hybrid NDT umbilicals for subsea weld phased-array ultrasonic, TOFD and ACFM crawlers
  • TF-OWIND-ROV-HYB: Neutral/floating hybrid umbilical combining light brush grooming, cathodic-protection (CP) stab probe and flooded-member detection
  • -FLT / -WVD: Buoyancy trim suffix: Stand-off Floating/Neutral (-FLT) to clear rock berms, or Wave-Damped Slight Negative (-WVD) for vertical chutes
Applications

TF-OWIND Monopile Cleaning, Jacket Weld NDT & Mooring Chains

Engineered for offshore wind service operation vessels (SOV), crew transfer vessels (CTV) and resident subsea inspection/cleaning spreads.

Offshore wind turbine yellow monopile in splash-zone waves with a clamping marine-growth cleaning and ultrasonic NDT ring crawler deployed from a service vessel crane on a high-visibility fluorescent-orange TF-OWIND umbilical cable
Splash-zone monopile marine-growth cleaning and weld NDT ring crawler operating from an offshore wind service vessel via TF-OWIND dynamic umbilical.
  • Clamping ring crawlers and magnetic monopile vehicles performing high-pressure cavitation or rotary-brush marine-growth removal (MGR) across splash zones and TP boat landings.
  • Circumferential and nodal weld NDT crawlers running multi-channel PAUT, TOFD, ACFM and flooded-member detection (FMD) on offshore wind jackets and monopiles.
  • Floating offshore wind (FOWT) mooring chain, bridle and dynamic inter-array cable bend-stiffener cleaning, optical 3D caliper measurement and corrosion inspection crawlers down to 300 m.
  • Subsea J-tube bellmouth, scour-protection rock-berm and impressed-current cathodic protection (ICCP) anode cleaning/survey hybrid ROVs.

TF-OWIND vs Shipyard Crawler, Ship Hull ROV & Net-Cleaner Cables

TF-OWIND Offshore Wind Crawler Umbilical vs Shipyard Magnetic Crawler vs Ship Hull ROV vs Aquaculture Net Cleaner
Robotic Umbilical SeriesPrimary Environment & HazardVoltage & Tensile RatingTarget Robotic System
TF-OWIND Series (this page)Splash-zone wave slam, mussel beds & rock berm690 V–3.3 kV; 22–110 kN MBLOffshore wind monopile MGR, mooring chain & weld PAUT/ACFM crawlers
TF-MCR Magnetic Crawler CableVertical steel ship hull & dry-dock UHP jetting500–1,000 V; ultralight 8–35 kNShipyard hydroblasting, paint-stripping & dry/wet hull NDT crawlers
TF-HULL Biofouling ROV TetherPort anchorage currents & vessel propellers400–1,000 V; neutral/floating trimFree-swimming & suction ship-hull biofouling cleaning ROVs
TF-AQUACLEAN Net Cleaner CableFloating salmon cages & fish-oil lipid water690–1,000 V; floating trim15–75 kW offshore aquaculture net-washing robots

Operating a dry-dock or vertical ship-hull magnetic hydroblasting crawler? Compare our ultralight TF-MCR Magnetic Hull-Crawling Robot Umbilical Cable.

TF-OWIND Offshore Wind Crawler Umbilical RFQ Checklist

  • Offshore wind asset & tool type: monopile clamping ring cleaner, jacket node PAUT/ACFM weld crawler, or floating-wind mooring chain inspection vehicle.
  • Power & voltage schedule: 690 V AC three-phase, 1,000 V DC or 3.3 kV MV power, motor/pump kW, and maximum allowable voltage drop over cable length.
  • NDT & telemetry channels: single-mode/multimode fiber count in stainless FIMT, Cat 6/6A Ethernet, 75-ohm coax count or shielded twisted pairs.
  • Catenary buoyancy target & sheave D/d: floating/neutral stand-off trim vs wave-damped negative vertical trim, minimum SOV/CTV sheave groove diameter and required MBL (kN).
  • Continuous drum length & quantity (50 m MOQ, supplied as bulk un-terminated cable on wooden drums with heat-shrink end caps in 7 to 45 working days).

Related selection resources

TF-OWIND Offshore Wind Cleaning & NDT Umbilical FAQ

Why do TF-OWIND offshore wind monopile cleaning umbilicals use contra-helical dual-braid synthetic armor?

2-layer opposed-angle aramid or LCP braiding cancels torsional rotation when splash-zone waves alternately slacken and snap-load the umbilical, preventing loop hockling and optical-tube kinking around monopile boat landings.

Should a TF-OWIND monopile cleaning umbilical be floating or slightly negatively buoyant?

2 deployment geometries dictate trim: CTV/SOV stand-off operations typically specify slightly floating (-10 to -15 kg/km) so slack stays above seabed rock-dump scour protection, whereas vertical deck-chute deployments along mooring chains specify +18 to +140 kg/km negative weight to damp wave surge.

Can TF-OWIND combine 690 V cavitation-pump power and phased-array ultrasonic (PAUT) coaxial channels in a single umbilical?

Yes — hybrid builds such as TF-OWIND-NDT-PAUT and custom MGR+NDT umbilicals isolate VFD power conductors with braided EMC shields while carrying 75-ohm low-loss coax, Cat 6A Ethernet and stainless-FIMT optical fibers for single-mobilization cleaning and weld inspection.

How does the TF-OWIND Shore 95A PUR sheath hold up against North Sea blue mussel and barnacle growth?

2.5 to 4.0 mm heavy-wall Shore 95A polyether polyurethane provides over 80 N/mm tear propagation resistance alongside inner elastomeric bedding, resisting shell lacerations and J-tube lip abrasion far longer than standard TPR or thin ROV jackets.

What is the minimum order quantity and lead time for TF-OWIND offshore wind crawler umbilicals?

50 m is our minimum order quantity per cross-section, delivered as continuous bulk cable on export wooden drums with heat-shrink water-blocking end caps in 7 to 45 working days.

Specifications

TF-OWIND 690 V–3.3 kV Cleaning & PAUT/ACFM Umbilical Schedule

TF-OWIND Splash-Zone Fatigue, 22–110 kN MBL & 50 m MOQ

  • Splash-zone wave-slam fatigue build: Contra-helical dual-layer aramid or LCP tensile braid (22–110 kN MBL) eliminates rotational pig-tailing under cyclic 2–4 m North Sea / Taiwan Strait wave surge in the +/-5 m splash zone
  • 690 V–3.3 kV cleaning & NDT hybrid: Combines 15–75 kW pump/thruster power cores with laser-welded stainless FIMT single-mode fibers, subsea Cat 6A Ethernet and 75-ohm low-loss phased-array ultrasonic (PAUT) coax
  • Mussel-cut Shore 95A extra-thick PUR: 2.5 to 4.0 mm radial thickness Shore 95A polyether PUR outer sheath resists razor-sharp blue mussel beds, barnacle collars, J-tube bellmouth chafe and CTV deck winches
  • Controlled splash or catenary trim: Available in floating/neutral trim (-15 to 0 kg/km) to avoid snagging seabed scour-protection rock dump, or wave-damped slight negative trim (+20 to +140 kg/km) for vertical chain crawlers
  • Continuous bulk drum supply, MOQ 50 m: Manufactured in continuous splice-free lengths from 50 m MOQ on seaworthy export wooden drums with heat-shrink water-blocking end caps in 7 to 45 working days
TF-OWIND Offshore Wind Monopile, Jacket & Mooring Chain Cleaning & NDT Crawler Dynamic Umbilical Cable (690 V–3.3 kV) technical data
ParameterValue
Rated voltage600/1000 V (690 V three-phase system compatible) on MGR and NDT series; 1.8/3.0 (3.3) kV medium voltage on TF-OWIND-CHAIN3K deep mooring-chain umbilical
Telemetry and NDT signal cores4 to 12 G.657.A2 fibers in stainless FIMT, shielded subsea Cat 6/Cat 6A Ethernet, 75-ohm low-loss PAUT coaxial cores and 100-ohm foil/braid ACFM twisted pairs
Breaking load and torque balance22 kN to 110 kN minimum breaking load (5.5 to 27.5 kN SWL) via contra-helical aramid or LCP yarn braids engineered against splash-zone snap loading
Outer sheath and buoyancy trimHeavy-wall 2.5 to 4.0 mm Shore 95A cut-resistant polyether PUR (Fluorescent Orange or Neon Yellow); floating/neutral (-15 to 0 kg/km) or wave-damped negative (+18 to +140 kg/km)
Supply form and MOQContinuous splice-free bulk cable from 50 m MOQ on export wooden drums with heat-shrink water-blocking end caps in 7 to 45 working days
Operating temperature and bend radius-35 °C to +80 °C North Sea / Baltic / East Asia offshore deck and subsea duty; minimum dynamic sheave bend radius 10 × OD (static 6 × OD)
Environmental and fluid resistanceResistant to seawater hydrolysis, hydraulic biodegradable esters, turbine gearbox synthetic oils, diesel slicks, ozone and continuous UV exposure on open SOV decks

Monopile, Jacket & Floating-Wind Mooring Chain Cleaning Umbilical Schedule

TF-OWIND Offshore Wind Monopile, Jacket & Mooring Chain Marine-Growth Cleaning Crawler Umbilical Schedule
Model & Duty TierPower & Control CoresOptical / Ethernet & TubeNom. OD (mm)Seawater Wt SG 1.026 (kg/km)Min. Breaking Load (kN)Primary Wind Foundation DutyNext step
TF-OWIND-MGR15 (690V)4 × 4.0 mm² + 2 × (2×0.5 mm² STPs)4 SM FIMT + Subsea Cat 621.5-10 (Slightly Floating)3215 kW monopile clamping brush/jet crawlerRequest this size
TF-OWIND-MGR37 (690V)3 × 10 mm² + 1G6 mm² + 4 × 1.0 mm²6 SM + 2 MM Stainless FIMT27.8-15 to +25 (Custom Trim)5537 kW splash-zone cavitation ring crawlerRequest this size
TF-OWIND-MGR75 (1kV)3 × 25 mm² + 3G4 mm² + 2P × 0.5 mm²8 SM FIMT + PA Pressure Tube35.4+140 (Wave-Damped)8575 kW jacket leg & J-tube heavy MGR toolRequest this size
TF-OWIND-CHAIN3K (3.3kV)3 × 6.0 mm² (3.3 kV) + 4 × 1.5 mm²8 SM G.657.A2 Stainless FIMT29.60 to +45 (Controlled)110300 m floating-wind mooring chain cleanerRequest this size

Subsea Weld PAUT, ACFM & Hybrid Inspection Crawler Umbilical Schedule

TF-OWIND Subsea Weld PAUT, TOFD, ACFM & CP Inspection Crawler Hybrid Umbilical Schedule
Model CodePower & NDT Coax / Shielded PairsOptical / Gigabit DataNom. OD (mm)Seawater Wt SG 1.026 (kg/km)Min. Breaking Load (kN)Primary Subsea NDT / Survey ApplicationNext step
TF-OWIND-NDT-ACFM4 × 1.5 mm² (1 kV) + 6 × (2×22 AWG STPs)2 SM + 2 MM Optical Tube16.8+18 (Low-Excursion)22Jacket node fatigue-crack ACFM & PEC magnetic crawlerRequest this size
TF-OWIND-NDT-PAUT4 × 2.5 mm² (1 kV) + 4 × 75 Ω Low-Loss CoaxSubsea Cat 6A + 4 SM FIMT19.4+35 (Wave-Stable)28Monopile circumferential weld PAUT & TOFD scannerRequest this size
TF-OWIND-ROV-HYB3 × 6.0 mm² (1 kV) + 2 × 75 Ω CoaxSubsea Cat 6 + 6 SM FIMT24.20 to -8 (Neutral/Float)45Combined brush grooming, CP probe & FMD ROVRequest this size

Splash-zone buoyancy strategy: choose slightly floating (-10 to -15 kg/km) when paying out from a CTV/SOV stand-off position so the catenary floats clear of subsea rock-dump scour protection; choose wave-damped slight negative trim (+18 to +140 kg/km) when deploying vertically down a monopile or mooring chain through a deck overboarding chute to minimize wave-crest excursion.

ASCII part references for BOM and ERP entry: TF-OWIND-MGR15, TF-OWIND-MGR37, TF-OWIND-MGR75, TF-OWIND-CHAIN3K, TF-OWIND-NDT-ACFM, TF-OWIND-NDT-PAUT, TF-OWIND-ROV-HYB.

Standards

TF-OWIND Offshore Dynamic Conductor, Dielectric & Optical Standards

TF-OWIND Offshore Wind Monopile, Jacket & Mooring Chain Cleaning & NDT Crawler Dynamic Umbilical Cable (690 V–3.3 kV) standards and test references
Standard or specificationApplication
IEC 60228 Class 5/6 & IEC 60502-1 (0.6/1 kV to 1.8/3.0 kV) Insulation DesignFine-stranded tinned copper conductors with water-tree-retardant XLPE/EPR insulation verified by factory AC/DC spark and dielectric withstand testing.
ITU-T G.657.A2 Optical FIMT, ANSI/TIA-568 Cat 6A & IEC 61196 CoaxLow-attenuation stainless-tube fibers, 100-ohm shielded Ethernet and controlled-velocity 75-ohm ultrasonic coaxial cores for real-time topside NDT imaging.

Certifications and document support

TEBAOFLEX ISO 9001 quality management, HV dielectric withstand and OTDR testing

IEC 60228 — Conductors of insulated power and control cables

ITU-T G.657.A2 Bend-Insensitive Optical Fiber Transmission Standard

Compare by duty

Related cable options

Compare these cable options by service combination, movement, load, voltage and transmission requirement.

Engineering-led quotation

Request a cable recommendation and quotation

Send the required services, cable length, mechanical duty, environment, termination and quantity. Our team will review the application before quoting.

  • Include the product name or SKU plus the required cable length and quantity.
  • Attach a specification, drawing or data sheet when available.

    MOQ 50 m · Engineering reply within 24 hours

    By submitting this form, you agree that TEBAOFLEX may use the contact information and files provided to review and respond to your enquiry. Files are used for quotation and engineering communication related to your request. See our Privacy Policy for current data handling and retention information.

    Email or WhatsApp is enough. Please include the key cable or application details for review.