MINING & TUNNELING CABLES TEBAOFLEX

36-129 Two-Conductor Blast-Hole Drilling Mast Cable (600/2000 V, 8 AWG–4/0 AWG)

36-129 (series 36-129-008 through 36-129-040) is a two-conductor 600/2000 V blast-hole drilling mast cable engineered with rope-lay tinned copper conductors (8 AWG to 4/0 AWG), 90 °C EPR insulation, integral rubber fillers, open nylon reinforcing braid and an extra-heavy-duty MSHA flame-resistant thermoset chloroprene jacket.

Product information
SKU
NA-36-129-MAST
Brand
TEBAOFLEX
Product overview

Rotary blast-hole drills, overburden rigs and raise borers subject vertical mast loop cables to simultaneous axial suspension weight, high-amplitude drill-string vibration, rotary head travel flexing and continuous bombardment from drill cuttings, hydraulic oil and sub-zero pit winds. Standard thin-wall Type W cords suffer jacket tearing and core corkscrewing when hung from a 15 m to 30 m drill mast.

The 36-129 two-conductor 600/2000 V drilling mast series (part numbers 36-129-008 through 36-129-040) resolves vertical mast fatigue by pairing rope-stranded annealed tinned copper conductors (133 wires in 8 and 6 AWG; 259 wires in 4, 2 and 1 AWG; up to 532 wires in 4/0 AWG) with 60 mil or 80 mil 90 °C ethylene propylene rubber (EPR) insulation in black and white circuit identification. The two power cores are cabled with full-profile rubber fillers to lock core circularity, wrapped with a reinforcing binder tape and reinforced by an open nylon braid bonded directly into an extra-heavy-duty thermoset chloroprene (CR) outer jacket.

Compared with standard single- or multi-core Type W cables, the 36-129 mast build carries a thicker outer wall—yielding a 0.99 in. (25.1 mm) overall diameter already at 8 AWG and 2.26 in. (57.4 mm) at 4/0 AWG—to absorb mast-guide slap and Chinese-finger grip compression. Specify 36-129 for two-wire DC or single-phase AC rotary drill mast loops, or select Type G-GC / SHD-GC where three-phase power with ground-check monitoring is required.

Explore the mining and tunneling cable range for related configurations.

Construction

36-129 Blast-Hole Drilling Mast Cable Construction & Reinforcement

The representative horizontal sample illustrates 36-129-002 (2/C 2 AWG, 1.48 in. nominal O.D.): black and white 90 °C EPR-insulated 259-strand tinned copper conductors cabled with cylindrical rubber fillers, reinforcing binder tape, open nylon braid and an extra-heavy-duty black thermoset chloroprene outer jacket.

Flat 2D cross-section diagram of 36-129 two-conductor 600/2000 V blast-hole drilling mast cable showing stranded tinned copper conductors, black and white EPR insulation, rubber fillers, binder tape, open nylon braid and extra-thick chloroprene outer jacket
36-129 cross-section: rope-lay tinned copper, 90 °C EPR insulation, fillers, binder tape, open nylon braid and thick CR jacket.
36-129 Two-Conductor Blast-Hole Drilling Mast Cable (600/2000 V, 8 AWG–4/0 AWG) construction
ComponentMaterial and construction
ConductorsFlexible rope-lay stranded annealed tinned copper (133 to 532 strands per conductor across 8 AWG to 4/0 AWG) meeting ASTM B33 and ASTM B 172.
Insulation & Colour Code90 °C ethylene propylene rubber (EPR), 60 mils (8–2 AWG) or 80 mils (1–4/0 AWG), colour-coded black and white.
Core Fillers & BinderTwo insulated conductors cabled with elastomeric rubber fillers to maintain a round anti-buckling profile under a reinforcing binder tape.
Reinforcing BraidHigh-tenacity open nylon braid embedded between the inner bedding/tape and outer elastomer wall to resist vertical stretch and core migration.
Outer JacketExtra-heavy-duty black thermoset chloroprene (CR) compound resistant to cutting, abrasion, drilling mud, diesel, sunlight and -40 °C cold impact; MSHA flame-resistant.

36-129 Part Number & Construction Breakdown

  • 36-129: two-conductor 600/2000 V extra-heavy-wall blast-hole drilling mast cable series
  • -008 to -001: AWG wire gauge suffix from 8 AWG (36-129-008) through 1 AWG (36-129-001)
  • -010 to -040: kcmil/aught wire gauge suffix from 1/0 AWG (36-129-010) through 4/0 AWG (36-129-040)
  • EPR / Nylon / CR: 90 °C EPR insulation, cabled rubber fillers, open nylon braid and MSHA thermoset chloroprene jacket
Applications

36-129 Two-Conductor 600/2000 V Drilling Mast Applications

Deploy 36-129 two-conductor 600/2000 V cables on vertical mast loops, travelling rotary head feeds and high-vibration surface or underground drilling equipment.

36-129 two-conductor blast-hole drilling mast cable suspended in a heavy-duty hanging loop along the vertical mast of an open-pit rotary blast-hole drill rig
36-129 600/2000 V blast-hole drilling mast cable operating in a vertical loop on a surface rotary blast-hole drill.
  • Vertical mast hanging loops and travelling rotary drive head power leads on open-pit rotary blast-hole drilling rigs.
  • Two-conductor DC armature/field feeds and single-phase 600/2000 V auxiliary power circuits on overburden drills and raise borers.
  • High-vibration mast-mounted motor, blower, hydraulic pump and floodlight circuits exposed to flying rock chips and drilling lubricants.
  • Direct part-number replacement for 36-129-008 through 36-129-040 mast cables in surface coal, copper, iron ore and gold mines.

36-129 vs Round Type W and Drill Cord Selection Boundary

36-129 Blast-Hole Drilling Mast Cable compared with related mining drill and portable power cables
ModelCores & size rangeWall & reinforcementBest fit
36-129 Mast Cable (this page)2/C, 8 AWG to 4/0 AWG (600/2000 V)Rubber fillers + binder tape + open nylon braid + extra-heavy CR jacketVertical blast-hole drill mast hanging loops & rotary head leads
Round Type W (600/2000 V)2/C to 5/C, 8 AWG to 500 kcmilStandard two-layer thermoset CPE/CR jacket with reinforce braidGeneral portable trailing power without severe mast slap
MSHA Double-Jacket Drill Cord2/C to 37/C, 18 AWG to 10 AWG (600 V)High-visibility dual thermoset rubber jacketsSmall-gauge remote control pendants and hand-held drill cords
Type G-GC (2000 V)3/C + 2 grounds + 1 ground-checkHeavy-duty two-layer thermoset jacketThree-phase AC mobile mining equipment requiring ground-check

Verify mast loop suspension grip diameter against the extra-heavy 0.99 in. to 2.26 in. nominal O.D. of the 36-129 series before ordering.

Related selection resources

36-129 Blast-Hole Drilling Mast Cable Frequently Asked Questions

Why does a blast-hole drill mast require the 36-129 construction instead of a standard 2-conductor Type W cable?

Vertical mast loops hang under constant self-weight while whipping against mast structural members as the rotary head travels up and down. The 36-129 series uses an extra-heavy-wall thermoset chloroprene jacket (for example 1.48 in. O.D. on 2/C 2 AWG and 2.26 in. O.D. on 2/C 4/0 AWG) over full rubber fillers, binder tape and an open nylon braid to prevent core corkscrewing and jacket splitting in mast cable grips.

How does conductor stranding scale across 36-129-008 through 36-129-040?

To maintain a 6 x O.D. minimum bend radius at the top mast sheave or travelling head clamp, 8 AWG and 6 AWG use 133 tinned copper wires, 4 AWG through 1 AWG use 259 wires, 1/0 AWG uses 266 wires, 2/0 AWG uses 323 wires, 3/0 AWG uses 418 wires and 4/0 AWG uses 532 wires.

When does nominal EPR insulation thickness increase from 60 mils to 80 mils?

Part numbers 36-129-008 through 36-129-002 (8 AWG to 2 AWG) are built with 60 mils (1.52 mm) of 90 °C EPR insulation, while larger sizes 36-129-001 through 36-129-040 (1 AWG to 4/0 AWG) step up to 80 mils (2.03 mm) to withstand higher mechanical compression on large mast sheaves.

What details should be confirmed when requesting a quotation for 36-129 mast cable?

Specify the exact part number (36-129-008 to 36-129-040) or AWG size, cut loop length or reel length, upper and lower mast basket/Kellems grip diameter range, and required test documentation.

Specifications

36-129 Part Numbers, Dimensions, Ampacity & Technical Specifications

36-129 Key Specifications

  • Part range: 36-129-008 (8 AWG) to 36-129-040 (4/0 AWG) two-conductor round mast cable
  • Voltage & ampacity: 600/2000 V rating; 54 A to 255 A continuous ampacity at 40 °C ambient
  • Conductor stranding: 133-wire (8–6 AWG), 259-wire (4–1 AWG) up to 532-wire (4/0 AWG) tinned copper
  • Mast reinforcement: Cabled with rubber fillers, binder tape and open nylon braid under extra-heavy CR jacket
  • Service envelope: -40 °C to +90 °C continuous rating; 6 x O.D. minimum bend radius; MSHA flame-resistant
36-129 Two-Conductor Blast-Hole Drilling Mast Cable (600/2000 V, 8 AWG–4/0 AWG) technical data
ParameterValue
Part number series36-129-008 to 36-129-040 (2/C 8 AWG to 2/C 4/0 AWG)
Voltage & temperature rating600/2000 V; -40 °C to +90 °C continuous conductor temperature
Diameter & weight range0.99 to 2.26 in. (25.1 to 57.4 mm) nominal O.D.; 670 to 4650 lbs/1000 ft (997 to 6920 kg/km)
Ampacity & bend radius54 A (8 AWG) to 255 A (4/0 AWG) at 40 °C ambient; minimum bending radius 6 x cable O.D.
Flame & mechanical complianceICEA S-75-381 / NEMA WC 58 heavy-duty thermoset construction; MSHA 30 CFR Part 7 flame resistance
Commercial supply termsMinimum order quantity 50 m; manufacturing lead time 7 to 45 working days; final values confirmed on the quotation drawing
Selection boundary vs Round Type W and Drill CordChoose 36-129 for 2-conductor 8 AWG to 4/0 AWG extra-heavy-wall 600/2000 V drill mast suspension; choose MSHA 600 V double-jacket drill cord for 16–12 AWG multi-core remote pendants, or Round Type W / Type G-GC for 3- and 4-conductor trailing power.

36-129 (36-129-008 to 36-129-040) Dimensional & Ampacity Schedule

36-129 Two-Conductor Blast-Hole Drilling Mast Cable (600/2000 V) — Part Numbers, Dimensions & Ampacity Schedule
Part No.Conductor SizeStranding (Wires)Nom. Insulation ThicknessNominal O.D.Approx. WeightAmpacity (40 °C)Next step
36-129-0088 AWG13360 mils (1.52 mm)0.99 in. (25.1 mm)670 lbs/1000 ft (997 kg/km)54Request this size
36-129-0066 AWG13360 mils (1.52 mm)1.10 in. (27.9 mm)890 lbs/1000 ft (1324 kg/km)72Request this size
36-129-0044 AWG25960 mils (1.52 mm)1.27 in. (32.3 mm)1250 lbs/1000 ft (1860 kg/km)93Request this size
36-129-0022 AWG25960 mils (1.52 mm)1.48 in. (37.6 mm)1800 lbs/1000 ft (2679 kg/km)122Request this size
36-129-0011 AWG25980 mils (2.03 mm)1.68 in. (42.7 mm)2270 lbs/1000 ft (3378 kg/km)143Request this size
36-129-0101/0 AWG26680 mils (2.03 mm)1.79 in. (45.5 mm)2680 lbs/1000 ft (3988 kg/km)165Request this size
36-129-0202/0 AWG32380 mils (2.03 mm)1.93 in. (49.0 mm)3200 lbs/1000 ft (4762 kg/km)192Request this size
36-129-0303/0 AWG41880 mils (2.03 mm)2.07 in. (52.6 mm)3627 lbs/1000 ft (5398 kg/km)221Request this size
36-129-0404/0 AWG53280 mils (2.03 mm)2.26 in. (57.4 mm)4650 lbs/1000 ft (6920 kg/km)255Request this size

36-129 Construction & Operating Parameters

36-129 Two-Conductor Blast-Hole Drilling Mast Cable — Construction & Operating Parameters
ParameterSpecification
Rated Operating Voltage600/2000 V AC / DC heavy-duty mast & hanging loop power
Conductor & InsulationFlexible stranded annealed tinned copper (133 to 532 wires) with 90 °C EPR insulation (black & white cores)
Core Assembly & ReinforcementTwo insulated conductors cabled with integral rubber fillers, reinforcing binder tape and open nylon braid
Outer Jacket CompoundExtra-heavy-duty black thermoset chloroprene (CR) elastomer jacket with integral tensile reinforcement
Operating Temperature & Bend Radius-40 °C to +90 °C continuous conductor temperature; minimum bending radius 6 x cable O.D.
Flame & Crush QualificationFlame-resistant in accordance with MSHA 30 CFR Part 7; built for vertical mast suspension and drill vibration

Ampacities in the 36-129 schedule are based on a single two-conductor cable in free air at 40 °C ambient and 90 °C maximum conductor temperature per ICEA S-75-381 / NEMA WC 58. Insulation thickness steps from 60 mils (1.52 mm) on 8 AWG through 2 AWG to 80 mils (2.03 mm) on 1 AWG through 4/0 AWG.

MSHA 30 CFR Part 7, UL 1277 TC-ER-HL, ICEA S-75-381 / NEMA WC 58 and CSA C22.2 No. 230 / No. 239 are cited as governing design and test references; TEBAOFLEX manufactures to the referenced construction parameters and confirms project-specific marking and test documentation on the quotation drawing.

ASCII part references for BOM and ERP entry: 36-129-008, 36-129-006, 36-129-004, 36-129-002, 36-129-001, 36-129-010, 36-129-020, 36-129-030, 36-129-040.

Standards

36-129 Standards & Test References (ICEA S-75-381, MSHA)

36-129 Two-Conductor Blast-Hole Drilling Mast Cable (600/2000 V, 8 AWG–4/0 AWG) standards and test references
Standard or specificationApplication
ICEA S-75-381 / NEMA WC 58Portable and power feeder cables for use in mines and similar applications (construction, EPR insulation, thermoset CR jacket and ampacity basis).
MSHA 30 CFR Part 7Flame-resistance test qualification reference for surface and underground mining cables.
ASTM B33 / ASTM B 172Specifications for tinned soft or annealed copper wire and rope-lay stranded copper conductors.
UL 44 / CSA C22.2 No. 38Thermoset-insulated wire and cable reference for 90 °C EPR dielectric performance.

Certifications and document support

TEBAOFLEX company certificates and quality system documentation

NEMA / ICEA S-75-381 (NEMA WC 58) portable mining cable standard reference

Compare by duty

Related cable options

Compare these cable options by service combination, movement, load, voltage and transmission requirement.

Engineering-led quotation

Request a cable recommendation and quotation

Send the required services, cable length, mechanical duty, environment, termination and quantity. Our team will review the application before quoting.

  • Include the product name or SKU plus the required cable length and quantity.
  • Attach a specification, drawing or data sheet when available.

    MOQ 50 m · Engineering reply within 24 hours

    By submitting this form, you agree that TEBAOFLEX may use the contact information and files provided to review and respond to your enquiry. Files are used for quotation and engineering communication related to your request. See our Privacy Policy for current data handling and retention information.

    Email or WhatsApp is enough. Please include the key cable or application details for review.